I think any plumber would tell you that the key to successfully for welding or "sweat" a copper connection correctly is to prepare the pipeline and connection to the welding process. Cleaning of pipe and fittings are essential for welding to flow properly and to ensure that pipe and fittings have been soldered together. Just for had renewed my bath room and using existing lines that raised the water from the top for bathroom. I replaced all branches or "feeds" to shower, toilet and washbasin. When you use the existing pipeline again together tube, cleaning and preparation are critical to ensuring good soldered connections and joints. I'll use my room bathroom as an example.
Food for my room of bath is 1/2? copper pipe, but because my position of toilet and shower would be slightly different, I decided to route my piping hot and cold different to accommodate changes. They needed to get a tee 1/arcminutes copper in the cold feed by what could run cold water for the shower and toilet. I turned off the main in my basement to stop the flow of water. Once I had the water, I could sweat the connection properly. If you are a beginner in the tube of sweating, you need to know that you will never get your connections properly welded already long as there is water in the pipe. Even if the sligtest amount, is sufficient to prevent that copper heating until the correct temperature. Using a tube cutter, cut the existing copper tube back to your desired length. A thing about cutters tube for beginners, gradually increasing pressure on the blade as you rotate it. Putting too much pressure for all at the same time can cause your pipe deformation during cutting.Once the pipe is cut and clear of all waters, it is time to prepare the tube and fitting for the existing sudor.Tubería will normally look dark brown smear where new piping or fittings will normally be bright.
Look at the existing pipeline and make sure that there are not any strawberries in the end will go where the connection. Use a small file to one pipe if necessary. Then take a piece of paper Emery and prevent the pipe from end to approximately one inch in until it is free to tarnish of shinyand. I like to take a piece of cloth clean and only clean pipe off when I ' m through with Emery paper. This cleans up any dirt or dust out of it. Then take a brush pipe 1/2 "and run it through the connection." If you don't have a pipe brush, you can use a piece of cloth Emery.Applied flow around the end of the tube and within the connection. drop the connection at the end of the tube until it slides all the way in. When sweating a tee, I like prepare all three pipes and sweat all them, so it must not overheat the pipeline and disturbing parts of the already completed connection.
Once you have your connection in place, it is time to light your propane Lantern. Adjust calls until you find a nice and stable blue flame. Remember that the weld will always flow in the direction of the heat so you neeed to place his torch in a position where the weld flows evenly around of pipe and fittings and extract inward toward the heat. On a tee, would you want to place the torch in the center of the bar of the cross and the heat from the bottom. This way you will heat all pipelines of three at the same time and the soldler are drawn inward toward the heat pipes connecting link. In the case of a level of 45 or 90 connection, place the flame from the bottom on the curved side of the connection. Once you have the flame in the Assembly, you will notice that the flow starting to bubble. You should be maintained with the watcching until it seems to flow dried and the color of the pipe and fittings enable deaf. Take your welding and start at the top of the pipe where is the end of the connection. Tap welding at this point, and when it melts, maintain power welding to go around the pipe in one direction and stop at the bottom. Then return to the top and do the same in the other direction. Putting the heat on the bottom and starting your welding at the top, fill in the area where the pipe enters connection because welding will flow into heat. Be sure to do this around all pipes connection. Once you are finished, remove the heat.If you are using to much of welding, you will have seconds where welding will remain moist.It can take a cloth and rub gently around the pipe and fittings to remove excess solder and so smooth.Now allow for connection and cool pipe down without impacting les.muchas welds are converted in cracked because they are not allowed to cool correctamente.Recomiendo doing some practice in the garage, of trying things real.Si you know someone who has done before, why not ask them to come from a beer and share their experience.
http://www.justcordlessdrills.com - where all
is about wireless holes
My name is Jim and I have been around tools throughout my vida.He participated in electronics, electricity trade and industrial during my career maintenance entire work. moved four years in the U.s. Marine Corps body as teams of testing and calibration técnico.También went to Luzerne County Community College where I studied electronics technology he worked as an industrial electrician, on the road as a service technician and as a mechanical industry during the past twenty years. maintenance I have worked for companies such as T.J. Lipton (soup and tea people), Cargill, and I am currently employed by PepsiCo in its Gatorade.Yo Division also I have my own website called http://www.justcordlessdrills.com, where you can get information about wireless holes and also find great deals if you have need of buy a wireless quality brand name punch.
No comments:
Post a Comment